Відео

Great video! Just echoing what so many have posted. FWIW, I unscrewed the green ground wire near the front during disassembly. This allowed me to more easily remove the wires connected to the element. I was able to pull element housing all the way out, and then disconnect wires.

Thanks. You explained it really well great job

bom e barato do jeito que gostamos no Brasil 👏👏👏👏👏👏👏

this worked for a year. today tape/penny fell off. i will try to use a plastic threaded screw/bolt i got lying around for a more permanent solution

It works , thank you so much 👍

Excellent detail!!! Great Job!!!!!

Subscribing. Thanks for the video.

Helped locate provlem but tape comes loose in summer heat.JUST BEND BRACKET UP

It worked for me.

Excellent explanation for a non-car guy like me who needs every thing explained. You are the best.

Also blow out the spindle with some compressed air after polishing that copper. Even though the wire in lacquered for insulation best to be safe.

Be very careful with the plastic pin holder. I sprayed ec cleaner and it warped/softened the plastic pin holder.

This seems so much more economical vs kaizen foam.

Thanks for your video and explanation, blessings.🤗

Great idea…just edit video..don’t need to see almost every cut

Worked great!!! Thx

A bit more mature on the music please. PBS children's show vibe is a little off putting.

Excellent, and clear. Thank you

Thank God it worked thank u very good video

Your video got me to thinking about something that won't fall off over time and the first thing that popped into mind of a simple thumb tack placed in the middle of the piece of rubber. This works and doesn't depend on tape which eventually may unwrap and penny fall to the floor. Thanks for you video. Helped me find a better fix.

What if the cable is broken ?

why is the stabilization activated for a trypod shot??? what a mess

Thank you 💯

Very helpful video. It was a little different on my 02 5.9L 4x4 1500. The starter is sort of cramped into a cubbyhole and just getting the bolts off (one bolt, one nut) was tough because the tight space, and then worming it out of it's cubby and back in again. Forget breaker bars and torque wrenches! All the same, couldn't have done it without you. Thanks!

It’s been 4 years since I decided to do the fluid change on my odyssey and still going strong with 345,000 miles on it.

Is it hard to replace for a woman to replace

@7:24 Those grooves are cut for balancing. NOT a defect or damage.

I’m having a similar problem in my ‘15 Accord 6MT, but it’s with my clutch pedal. There is a small (<1cm) amount of play in the pedal before resistance starts, and cruise only sets when it is slightly pushed in. The pushpin sensor is threaded, so it would make sense to me if it can just be tightened down ever so slightly. I’m worried doing so might cause wear on my clutch though. Has anyone else experienced this issue? Thank you!

This video was stupendous!!!!

Worked! Thanks!

Yeah right! I needed to know what the wires look like because I forgot how they go together and this was a waste of time for me because he cuts off when he is connecting them back

Very useful video, thank you very much

This looked like an Acura Integra starter. I’m here trying to find out what grease to use and I got that info, thanks for that!

Thank you!

Everytime I put the car into drive or reverse, the third brake light on the dashboard keeps lighting up. This problem occurred when I recently changed the light bulb to LED. However, I changed it back to the original light bulb but it still won't go away. What is wrong?

What else could it be if this is not the case?

for me the door doesnt not close at all, no beep from it or anything, 2007 odyssey

Gonna work on removing 35 year old TO TA letters off a truck tailgate

thanks, my actuator is discontinued and this gave me confidence to know i can just replace the motor inside, fairly simple

I just did this and it lasted about 20 minutes it was super hot on medium setting it turned off by itself and wouldn't go to any other settings. I had to manually turn it off, so i turned back on and left heat on a really low setting and still got hot and shut off after about 3 minutes. So i gotta check what i did wrong, but i know i put all wires back how tgey were with the old one and the heating element.

🤞🏼I hope this works!

It’s like a Christmas bulb. Do you have about the temperature ac fan & heat bulb? TIA

I recommend that you do not remove the radiator cap before you begin to drain. This way, it will drain much slower until you are sure you have yourself out of the way of spilling liquid and the drain pan in place. Then, remove the radiator cap. Use this method on any vehicle. You’re welcome! lol

Did this job yesterday on a '03 Ram 1500 2WD Automatic. Everything shown in this video was dead-on. I even decided to use the 5/8" socket rather than a 16mm as it was a tighter fit to the mounting bolts. I used a universal joint with the socket/ratchet, but I really didn't need to. I was able to use my 1/2" torque wrench to torque the mounting bolts to 50 ft-lb (as specified in the service manual) without using an extension for either bolt. The toughest thing for me was getting the electrical connector fully seated on the new starter (AutoZone Duralast) as the connector didn't want to insert far enough to "latch" the retaining clip. I eventually got it to hold.

Jeff this instruction vedieo is great. I and my wife did the replacement within 2.456 hours, hehehee. But it now works. You saved us a lot of money by not hiring a mechanic. We will be watching out for more of your video's.

It would have been nice to know to take note of the placement of the elements at the beginning and not at the rushed through replacement.

Why does mine not work? They said add fluid but fluid is coming out of it when I open the fill hole

If that was the problem, your brake lights would stay on all the time, even when car shut off, resulting in dead battery if you don't spot it.

En español por favor

Thank you for your teaching! But we follow the video and change to the brand new heating stuff, and we put the door and follow all the instruction, but when we turn on the power it turn off by itself like in 5 seconds, do you know the why it turn off the power?